Shredder

Introduction

Wood crusher is an advanced fine crushing equipment, which is a series of products that absorb the advantages of various crushers and fully utilize theories such as impact, shear, mutual impact, and grinding to meticulously innovate. The shape, size, and discharge fineness of the feeding port of the wood crusher can be customized according to the actual needs of users.

Characteristic

1. The machine is structurally divided into a main machine (wood crusher main machine) and auxiliary machines (airflow separator, induced draft fan, powder collector, dust collector). A powder collector (also known as a centrifugal separator) is a device that allows powdered particles that meet the crushing requirements to enter the powder collector tangential to the airflow of the induced draft fan through the air duct, causing the airflow carrying the powder to rotate. The powder particles are then thrown towards the cylinder wall, settled at the discharge port, and enter the powder collection bag on their own.

2. The induced draft fan is a centrifugal fan that mainly provides suitable air pressure and volume for the unit, and plays a role in dust removal.

3. The main body of the dust collector is a box, and there is a ash door at the bottom of the box. The box should be installed in a vertical frame. The upper body of the vertical frame is covered with filter bags, and the dust collector receives dusty gas from the centrifugal separator. Enter the box from the entrance and discharge into the external space through the filter bag. Due to the fact that the dust removal efficiency of the bag filter can reach over 99%. When the filter resistance of the dust collector increases, you can choose to stop the machine and manually clean it during the rest time. When cleaning the dust collection bag, you can shake the filter bag by hand for tens of seconds to shake off the dust stuck on the surface of the filter bag. The shaken dust can be directly discharged into the dust collection bag through the ash door of the box, and then removed. Green and environmentally friendly, complete.

Applicable scope

1. Wood category: pine, miscellaneous wood, poplar, cedar, logs, bamboo, waste scraps, sawdust, sawdust, particleboard, nailed construction formwork, charcoal, activated carbon, etc.

2. Branches: branches, branches, roots, leaves, bark, etc.

3. Edible fungi: plant roots, stems, leaves, flowers, fruits, various edible fungi, etc.

4. Agriculture: straw, traditional Chinese medicine, tobacco stalks, grains, corn cobs, cellulose, potato residue, tea, hair, soybean meal, cotton, refined cotton, cowhide, sheepskin, etc.

5. Food category: dehydrated vegetables, hawthorn, ginger, garlic slices, pumpkin powder, seasoning, jujube, seasoning, feed, distiller's grains, furfural, cakes, etc.

6. Difficult characteristic materials: mica, graphite, bentonite, perlite, shrimp skin, fish meal, shells, seaweed, marine products, etc.

Customization of hundreds of difficult and characteristic materials, with a crushing degree that can achieve the desired effect of user customization!

Technical parameter

Operating instructions

1. Connect the power and check if the steering is correct.

2. When replacing the cutting tool, extend the cutting edge 2-4mm beyond the flat surface of the cutterhead, and then tighten the bolt. If the pressure bolt thread is found to be worn, it should be replaced immediately to prevent damage to the sliding disc nut.

3. To change the extension and retraction of the knife, it is necessary to extend the length of the knife uniformly.

4. By adjusting the length of the blade, if the particle size cannot reach the desired level, switch to a different aperture sieve.

5. It is strictly prohibited to throw firewood with stones and nails into the machine to prevent damage to knives and internal components.

6. Pay attention to checking the hammer bolts. If any looseness is found, tighten them immediately. If the hammer and bolts are severely worn, they should be replaced.

7. The grinding angle is a straight line of 28-30 °, and it is strictly prohibited to grind it into a convex surface.

Thank you for browsing the Henan Maoxin Machinery Equipment Co., Ltd website [Shredder] products! Maoxin Machinery is a Shredder product Chinese supplier. Since its establishment, it has been deeply engaged in the Lithium battery and circuit board recycling field and has to provide innovative Shredder products for Lithium battery and circuit board recycling customers! Stand up to the tide of change, dare to innovate, and create brilliance together 

---

In the online marketplace, differentiation is the key to winning business. Your product needs to stand out. Please contact us.

We respect your privacy. We Hate Spam As Much As You Do !

Headquarters

HENAN, CHINA
Gongyi City West Industrial Zone, Henan Province, China
Phone: +86 18539447368
Whatsapp: {whatsapp}