As a type of environmental waste gas treatment equipment, it exists and is divided into circulating water spray towers according to its working principle. According to the material of the tower, it is divided into fiberglass spray towers, PP spray towers, and stainless steel spray towers. Choose a reasonable spray material and spray process based on the different properties of the exhaust gas. The exhaust gas is introduced into the PP spray tower through the air duct. After passing through the packing layer, the exhaust gas and sodium hydroxide absorption liquid undergo gas-liquid two-phase full contact absorption and neutralization reaction. After purification, the acid mist exhaust gas is dehydrated and demisted by a defogging plate before being discharged into the atmosphere by a fan. The absorption liquid is pressurized by a water pump at the bottom of the tower and sprayed down at the top of the tower. Later, it flows back to the bottom of the tower for recycling. The purified acid mist exhaust gas meets the emission requirements of local emission standards.
Pay attention to current affairs and understand the overall situation, and concentrate on strengthening Huaxia [Water spray tower equipment] customer from Erdente, hello! Today is 2025-10-12. Since the Maoxin website http://www.cnchangtong.com was built, you are the 58456th visitor to Maoxin enterprise! Everyone takes action to save energy and reduce emissions, and enjoy a low-carbon life Maoxin has been committed to technology exploration and product promotion in the Lithium battery and circuit board recycling field since its establishment, and has accumulated to provide efficient [Water spray tower equipment] products for many customers!
As a type of environmental waste gas treatment equipment, it exists and is divided into circulating water spray towers according to its working principle. According to the material of the tower, it is divided into fiberglass spray towers, PP spray towers, and stainless steel spray towers. Choose a reasonable spray material and spray process based on the different properties of the exhaust gas. The exhaust gas is introduced into the PP spray tower through the air duct. After passing through the packing layer, the exhaust gas and sodium hydroxide absorption liquid undergo gas-liquid two-phase full contact absorption and neutralization reaction. After purification, the acid mist exhaust gas is dehydrated and demisted by a defogging plate before being discharged into the atmosphere by a fan. The absorption liquid is pressurized by a water pump at the bottom of the tower and sprayed down at the top of the tower. Later, it flows back to the bottom of the tower for recycling. The purified acid mist exhaust gas meets the emission requirements of local emission standards.
When dusty or oily waste gas passes through the spray tower, a suitable position inside the tower (depending on the design) sprays out liquid media, some are alkaline solution, and some are sulfuric acid solution. If the exhaust gas contains acidity, choose alkaline spray to neutralize the acidity. If the exhaust gas contains alkalinity, choose sulfuric acid solution for absorption. The specific choice of acid-base solution depends on the nature of the waste gas and the situation of the enterprise itself. No acid or alkali, but oily or dusty waste gas can be treated by spraying a circulating water solution. When the exhaust gas enters from the bottom of the tower, it comes into contact with the spray medium sprayed out by the spray tower. After contact, the exhaust gas or oil pollution is wrapped in water droplets, and the water droplets that wrap the pollutants collide again, increasing the surface area and gravity. Under the influence of gravity, water droplets that wrap around pollutants fall into the bottom of the spray tower, with heavier pollutants settling at the bottom of the tower and lighter pollutants floating on the surface of the circulating water body.
1. When the exhaust gas contains oil and dust, it is necessary to consider whether to add filter fillers or nozzle models when designing the spray tower. Choosing an inappropriate nozzle can easily cause blockage in the spray tower water system.
2. Choose the appropriate spray medium.
3. Design reasonable airflow channels and water supply methods.
4. Wastewater discharge and cleaning issues after spray tower spraying.
5. Choose the appropriate water pump based on the appropriate gas-liquid ratio.
6. The flow rate of an empty tower is generally designed to be 1-6 meters per second. But in the case of medium spraying and filling, the filtering wind speed can be reasonably selected based on the specific situation of the exhaust gas.
A hundred-year journey, the history of the Ming Dynasty, the enlightenment of thought; a hundred-year dream, the concentration of the heart and the sonorous actionIn today's manufacturing industry, the spirit of craftsmanship remains important.Henan Maoxin Machinery Equipment Co., Ltd has been dedicated to People-oriented, integrity management for many years, sticking to the Lithium battery and circuit board recycling field, and polishing "craftsman" level talents on Water spray tower equipment! Shoulder a new mission and show new actions
Maoxin takes Erdente friends to see China! China's history spans five thousand years, providing valuable insights into human survival and culture.
|
Hello,Erdente friends,Contact and cooperate, open the door to understanding China!
Gongyi City West Industrial Zone, Henan Province, China
Phone (WeChat): +86 18539447368
Email: 18539447368@163.com